Segregating Inventory Using Default Status and PO Blocking
Short answer
CE Set default inventory status on the item and assign a blocked status to the inbound purchase order from VendorB to segregate both current and future brake inventory.
Question
Which two actions should you perform? Each correct answer presents part of the solution.
NOTE: Each correct selection is worth one point.
Key Takeaways
The trap is focusing on disposition codes; the correct approach uses item-level default status for existing stock and PO-level blocking for future receipts.
Learn how to segregate inventory for brakes by setting the default inventory status on the item and blocking inbound purchase orders from the new vendor in MB-330.
Common mistake: Candidates often choose 'Create a disposition code' because it sounds like a quality control measure, but disposition codes are applied post-receipt, whereas this question requires pre-receiving segregation.
Expert Analysis
Default Inventory Status Controls Existing Stock Setting the default inventory status on the item ensures that all existing stock is immediately subject to the new control. In Dynamics 365 Supply Chain Management, inventory status determines if an item can be used in transactions. By setting this at the item level, every unit currently in the warehouse is automatically flagged for segregation without needing individual adjustments.
Inbound Purchase Order Blocking Handles Future Receipts Since Vendor A is being replaced and no further orders will come from them, blocking future POs from Vendor A is irrelevant. The scenario requires segregating inventory received from the new vendor (Vendor B) until testing is complete. Assigning a blocked status to the inbound purchase order from Vendor B prevents these specific items from being received into usable stock, ensuring they remain segregated upon arrival.
Why Other Options Fail Disposition codes are typically used after an item has been received but found to have quality issues, not for pre-receiving segregation. Item filter codes are for categorization and reporting, not for enforcing transactional blocks or segregation controls.
Exam Strategy
When asked to segregate inventory, always consider the lifecycle of the items: existing stock needs an item-level setting (default inventory status), while future receipts need a process-level block (inbound PO status). Disposition codes are reactive, not proactive segregation tools.
Frequently Asked Questions
Why not use a disposition code for segregation?
Can I use an item filter code to segregate inventory?
Community Votes
50% of anonymous learners picked answer C. Votes are pick records left by other test-takers — they are not the verified answer.
Discussion 10 contributions
Compiled from public community threads and reader submissions, lightly edited for clarity. Handles and vote tallies are shown as recorded, and comments reflect the views of individual contributors.
From public community threads 10
-
Erikj 👍 19Would say C and E. Inventory from vendor A is already in stock and will not be purchased anymore from vendor A. An item filter code is applicable to an item itself, so no way of segregating inventory. By both C and E new received inventory will get a different inventory status.
-
Sam_Onyx 👍 2I would go with A and C. Which are: (A) Put inbound purchase order from the Vendor A on hold is as good as putting the vendor on Hold. (C) Inventory status can be used to block the quantity of bicycles with brakes failures. These setups has nothing to do with the item number, since the case study says that same item number will be used for Vendor A and Vendor B.
-
Anthony_D 👍 2Agreed. All brakes in inventory (from A) as well as those received in the future (from B) must be tested. So we use default inventory status for brakes already in inventory, and inventory blocking for the new ones
-
Deciashay 👍 2seems correct
-
globeearth 👍 1-> B. Create a Disposition Code ✅ Disposition codes are used to categorize inventory based on quality, damage, or testing requirements. You can create a disposition code like "Pending Quality Check" or "Hold for Testing" and assign it to the brakes from VendorA that need to be tested. This allows tracking the status of the brakes without affecting other inventory movements. -> C. Set Default Inventory Status on the Item ✅ You can set the default inventory status to "Blocked" or "Quality Hold" for this item. This prevents the brakes from being sold or used until testing is complete. This is the best practice for controlling inventory status during quality checks.
Show 5 more comments
-
Gemami 👍 1- C. Set default inventory status on the item: Establishes a default status such as Blocked for brake inventory received in the future. - E. Assign a blocked status to VendorB's inbound purchase order: Ensures incoming VendorB brakes remain unavailable until testing is completed. Why not others? - A: VendorA is being replaced, so new inbound orders should be from VendorB. - B: Disposition codes support warehouse receiving processes, but aren't specifically required. - D: Item filter codes don't block inventory.
-
Deetss 👍 1Re-reading the answers, I think I would go with C & E. As said by Erikj & Anthony_D, VendorA won't be ordered from again & all inventory is in stock. Additionally, I believe E is poorly worded and is indicating changing the inventory status of brakes on newer and existing inbound orders from VendorB to a blocked status to ensure it gets checked & segregated. https://dynamics-tips.com/inventory-status-explained-d365-finance-and-operations/
-
globeearth 👍 1Why not A or E?: Both focus on inbound purchase orders, not existing inventory, making them irrelevant to the current stock. Why not D?: Item filter codes are for categorization, not segregation or control.
-
SDK_1234 👍 1This makes sense since there are no brakes from Vendor B, it still needs approval, so all the inventoried brakes are from Vendor A. No need to filter current inventory.
-
982be89 👍 1C is wrong. Because “Blocked” can prevent inventory from being used, but C says “Set default inventory status on the item.”
Reader comments & corrections
No reader corrections yet — spotted an error or have a note? Share it below.