GLBP and VSS: Both Gateways for Every VLAN Host

350-401 By islever Editorial Last updated

Explain the different design principles used in an enterprise network Layer 3

Short answer

BC GLBP provides one virtual IP with multiple forwarding MACs and VSS makes the two distribution chassis one logical gateway that both forward, so every host in the VLAN can use both switches.

Question

A network administrator has designed a network with two multilayer switches on the distribution layer, which act as default gateways for the end hosts. Which two
technologies allow every end host in a VLAN to use both gateways? (Choose two.)
  1. VRRP
  2. GLBP Correct Answer
  3. VSS Correct Answer
  4. MHSRP
  5. HSRP

Key Takeaways

The question tests the difference between one logical gateway shared by all hosts (GLBP/VSS) and per-group gateway redundancy (HSRP/VRRP/MHSRP), with the trap being load-balancing options that actually force hosts onto different default gateways.

GLBP (B) and VSS (C) are the two technologies that let every host in a VLAN use both distribution-layer gateways, while HSRP, VRRP, and MHSRP either keep one gateway idle or divide hosts across separate virtual IPs.

Common mistake: The most plausible wrong pick is MHSRP (D) because it is marketed as gateway load balancing, but it creates two VIPs and therefore splits hosts between default gateways rather than letting each host use both switches.

Expert Analysis

The requirement is per-host, not per-group

The question does not merely ask for gateway redundancy; it asks for a design in which every end host in the VLAN can use both multilayer switches. That wording rules out any FHRP that elects one active forwarder per virtual gateway and leaves the other idle under normal conditions. HSRP (E) and VRRP (A) both present one virtual IP/MAC with a single active router, so neither lets every host use both gateways.

MHSRP is the strongest trap

MHSRP (D) sounds attractive because multiple HSRP groups provide load sharing, but it does so by creating two distinct virtual IPs. Hosts must then be split between default gateways, so a given host uses only one of the two switches. The comments make this point: MHSRP “presents 2 VIPs,” which is not the same as every host using both gateways.

What satisfies the wording

GLBP (B) keeps one virtual IP for all hosts but distributes multiple virtual MAC addresses across the gateway routers, so the host community uses both switches while retaining a single default-gateway address. VSS (C) goes further at the platform level: the two distribution chassis become one logical switch with one control plane, and both chassis forward traffic for the same virtual gateway. A comment on the VSS guide notes that with VSS a “single gateway is configured and the load is balanced between two switches.” Together B and C meet the question’s per-host qualifier; A, D, and E do not.

Official Reference

Exam Strategy

When a first-hop redundancy question asks which technology lets every host use both gateways, underline both qualifiers. HSRP and VRRP fail because only one device is active per group; MHSRP fails because it creates separate VIPs and therefore separate default gateways for different hosts. Look for a single logical gateway presented by the pair—GLBP's one VIP with multiple AVFs or VSS's one control plane across two chassis—which is the pattern the exam rewards.

Frequently Asked Questions

Why is MHSRP not the answer if it is often described as gateway load balancing?

MHSRP creates multiple HSRP groups with separate virtual IP addresses. That lets you distribute different hosts across different default gateways, but each host still uses only one gateway; it does not let every host in the VLAN use both switches.

How does VSS let both distribution switches act as the default gateway?

VSS combines the two chassis into one logical switch with a single control plane. The default-gateway IP is configured on that virtual switch, and both chassis can forward traffic, so every host uses the pair rather than one active and one idle switch.

More 350-401 FAQ →

Community Votes

B
48%
D
32%
C
19%
A
1%

48% of anonymous learners picked answer B. Votes are pick records left by other test-takers — they are not the verified answer.

Discussion 94 contributions

Compiled from public community threads and reader submissions, lightly edited for clarity. Handles and vote tallies are shown as recorded, and comments reflect the views of individual contributors.

From public community threads 30 of 94

  1. TTTTTT 👍 43
    GLBP and MHSRP ------Correct
  2. laterst 👍 39
    I'm going for B and C. VRRP - and HSRP suffer from that fact that they both have one primary/master router which provides the _single_ default gateway (single VIP, single virtual MAC) MHSRP provides two Virtual IPs, so end hosts would have to be configured with two default gateways - not common for end hosts. The same concept would apply to multiple VRRP groups. GLBP provides one virtual IP and multiple virtual MAC Addresses; the ARP replies from the Active Virtual Gateway to the hosts will use all the virtual MACs (one for each virtual forwarder) in round robin fashion, so B is correct. which leaves VSS, where both ML Switches form a single virtual switch and no FHRP is required at all to use them both.
  3. Matt2727 👍 17
    The question is asking which 'technology' allows 'every' end host. Its not asking about a specific protocol. B & C make the most sense since 'every' end host can use both gateways. MHSRP requires a splitting of end hosts to use 1 particular gateway and is configured with 2 groups on the active standby routers.
  4. mhizha 👍 11
    I agree with your 2 answers. People need to understand that VSS is NOT classified as a FHRP
  5. iz_m6 👍 6
    The key words in the question are “One VLAN” and “both gateways” (as in two different gateways)! VRRP & HSRP are similar and cannot satisfy both requirements so they are incorrect! VSS is about pairing two switches together into one, therefore does not satisfy the requirement for two gateways. So by the method of exclusion, GLBP & MHSRP are the only logical answers left! B & D are the correct answers!
Show 25 more comments
  1. Satoshi08 👍 6
    every end host in "ONE VLAN" to use both gateways This "ONE VLAN" is the key to solve this question. Configuring MHSRP, you use routed port(by configuring "no switchport"). So MHSRP is wrong. B, C is the correct. https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9600/software/release/16-11/configuration_guide/ip/b_1611_ip_9600_cg/configuring___hsrp.html
  2. error_909 👍 5
    B&C Either we use GLBP with FHRP or combine both Distributed switches with VSS into one logical switch which in this case will automatically remove the need for FHRP: MHRP and VRRP only distribute the load between them, by assigning different masters for a group on each of them, but will not make all end hosts to use both.
  3. iGlitch 👍 4
    "ONE VLAN", MSRP is implemented on MULTIPLE Vlans and doesn't provide load balancing. The question considers switches as gateways, and the goal is to utilize both gateways and not specifically for load-balancing. So the key is ONE VLAN. GLBP provides load-balancing in ONE VLAN. VSS combines two switches, provides utilization of both switches, and NOT necessarily load-balancing.
  4. Asymptote 👍 4
    VSS combine two switches into one logical switch. both of them have their own control and data plane, both of their data plane will keep alive, once the master control plane is down, the other take charge. MHSRP mhsrp can't let all host use both gateway, 50% host use gateway1, another 50% host use gateway 2 (fromWINDSON)
  5. msstanick 👍 4
    It is B & D. 31 days before CCNP exam page 194: "HSRP does not support load sharing as part of the protocol specification. However, load sharing can be achieved through the configuration of MHSRP". I "love" Cisco - their official CERT guide says nothing about that solution so you basically need to buy another book...
  6. teikitiz 👍 4
    I don't think "allow every end host in a VLAN to use both gateways" can be met with MHSRP. True, VSS isn't a FHRP but can't agree with MHSRP as a solution that meets the above criteria
  7. rpidcock 👍 4
    The key in this question is using "both gateways, i.e. load balancing". That is accomplished using either GLBP or MHSRP.
  8. BuzzLightBeer 👍 4
    I hate this questions because VSS is the better design, but GLBP and MHSRP I believe are correct.
  9. aohashi 👍 4
    It should be B,D
  10. DLLLLLLLL 👍 4
    B & C !
  11. SwitchKiller 👍 3
    A lot of the discussion I’m reading here is making reference to Load Balancing/Sharing as reasons for the answer but the Question doesn’t mention or ask for this. We just need to identify the Technologies that will allow every host to use both Gateways. VRRP & HSRP both present a Virtual IP that will only be present on 1 device at a time, so that would eliminate both. MHSRP, presents 2 VIP’s, with the design idea being that half your users will get 1 VIP the other half the 2nd VIP. Again this would eliminate it as an option. This only leaves GLBP & VSS as our options. GLBP, everyone seems to agree is correct. With VSS, as I understand it, the Switches will be seen as a single logical switch so a Host could communicate with either switch and its data would be passed between the Switches, for forwarding, thereby in my opnion meeting the Question criteria of allowing a Host to use Both Gateways
  12. pulseberg 👍 3
    The correct answer is B. GLBP and E. HSRP. VRRP (Virtual Router Redundancy Protocol) and HSRP (Hot Standby Router Protocol) allow multiple routers to participate in a virtual router group to share the traffic load, but only one router is active at a time. MHSRP (Multigroup HSRP) is a Cisco-proprietary protocol that allows for load balancing between HSRP groups, but it still only allows one active router per group. GLBP (Gateway Load Balancing Protocol) allows multiple routers to participate in a virtual router group and actively load balance traffic between them. This allows for the use of multiple default gateways in the same VLAN. VSS (Virtual Switching System) is a Cisco-proprietary technology that allows two physical switches to act as a single logical switch. While VSS provides redundancy, it does not allow for load balancing between the two switches.
  13. zbeugene7 👍 3
    I was wrong , correct answer BC. First of all the requirements read: "A network administrator has designed a network with two multilayer switches", multilayer, when the two switches are configured as VSS, a single gateway is configured and the load is balanced between two switches , when VSS is connfigured virtual switch domain is established. Then, you can configure the virtual IP address on the appropriate VLAN interface(s) within the VSS. So every host configured with this VIP would use both switches. MHSRP on the other hand can be configured to use only single gateway as a master(primary) per group do if you have two groups with different master half of the hosts would use one, and the other half would use the other, so not every host can use both, correct, so MHSRP is no go.
  14. Burik 👍 3
    It's obviously B and C. It's asking which two TECHNOLOGIES allow to use BOTH gateways, it's not asking which redundancy PROTOCOLS you could use. GLBP will provide load balancing at Layer 3, VSS will provide load balancing at Layer 2. Therefore meeting the design request. As mentioned in the question, this is a design question, and no designer in his right mind would use MHSRP if VSS and GLBP are an option. The other FHRP answers are there just to confuse you.
  15. Brand 👍 3
    I think the key here is "allow every end host in a VLAN to use both gateways". VRRP, HSRP or MHSRP can't allow "every end host" to use "both" gateways at the same time. But MCEC protocols like VSS, StackWise or vPC allows two gateways to act as one physically and virtually. So I'll go with GLBP and VSS for this one as the other answers can't really seems to provide what is asked.
  16. cwauch 👍 3
    B. GLBP - provides gateway redundancy for endpoints and load balancing D. MHSRP - provides gateway redundancy for endpoints and load balances by using multiple HSRP instances. * VSS - I feel this is wrong because the question talks about the distribution layer, where the above FHRPs would be used and VSS is used at the core layer upstream of the where the gateway resides.
  17. wamendoza 👍 3
    After reviewing carefully, i see this in the question: "A network administrator has designed a network with two multilayer switches on the distribution layer," This it makes me think that he is talking about two separate switches (sw 1 & sw 2)... This is the problem, VSS cannot be a options because is a physical switch that see how one, so I would rule out this option...
  18. Yaa_Man_ 👍 3
    Guys, I think the term we're looking for it's load sharing If so: VRRP - does not support load sharing GLBP - support load balancing, thus supports load sharing as well VSS - the question states that there are 2 distinctive switches MHSRP -it does support load sharing HSRP - does not support load sharing Final answer B D
  19. Klimy 👍 3
    VSS makes more sense than "MHSRP". MHSRP is just an administrative load balancing, so "in a VLAN" PCs wouldn's use both gateways. As D is incorrect and you still have to X something, i would go with VSS. This question is faulty.
  20. Soggyt74 👍 3
    GLBP and VSS both support allowing all hosts to use both pathways. MHSRP ties hosts to a single pathway, and will only use the other pathway in failover.
  21. WINDSON 👍 3
    answer is GLBP and VSS mhsrp can't let all host use both gateway, 50% host use gateway1, another 50% host use gateway 2
  22. AbdullahMohammad251 👍 3
    VSS and GLBP are the only two technologies, among the options provided, that offer load balancing and redundancy.
  23. rogue_user 👍 3
    GLBP and MHSRP both support load balancing. VSS is not FHRP.
  24. Blue_Water 👍 3
    GLBP and MHSRP
  25. Chuchu_stima 👍 2
    MHSRP allows multiple HSRP groups to be configured on the same VLAN or interface, with each group having its own virtual IP address (VIP) and active/standby router pair. This configuration provides additional redundancy and fault tolerance, as it allows for more than one default gateway on the same network segment. In MHSRP, each router in the HSRP group has a priority value, and the router with the highest priority becomes the active router. If the active router fails, the router with the next highest priority takes over as the active router and starts forwarding traffic. MHSRP can be used in environments where redundancy and high availability are critical, such as data centers or enterprise networks. However, configuring multiple HSRP groups on the same VLAN or interface can increase network complexity and may require additional management overhead. It is recommended to carefully plan and test the MHSRP configuration before implementing it in a production environment.

Reader comments & corrections

No reader corrections yet — spotted an error or have a note? Share it below.

Log in to comment, report an error, or add a note about this question.

Practice All 350-401 Questions

Access 218 questions with complete answers and detailed explanations.

View Full 350-401 Practice Test →

← Back to 350-401 Study Guide