Fixing Imminent Drive Failure SMART Alert

220-1201 By islever Editorial Last updated

Short answer

A Replace the hard disk, as the SMART alert indicates physical hardware failure that requires component replacement rather than software fixes.

Question

A user reports the following error message to the help desk:
Drive failure imminent
The user presses F1 to continue past the error and work like normal. Which of the following should the help desk technician do to fix this issue?
  1. Replace the hard disk. Correct Answer
  2. Reformat the partition.
  3. Rebuild the array.
  4. Enter safe mode.

Key Takeaways

The main trap is ignoring the SMART alert's severity or attempting software repairs like reformatting; the insight is that SMART warnings indicate physical failure requiring immediate hardware replacement.

Resolve the 'Drive failure imminent' SMART alert by replacing the hard disk. This CompTIA A+ 220-1201 question tests knowledge of hardware monitoring and preventive maintenance.

Common mistake: Users might choose to rebuild the array (C) if they mistakenly assume a RAID setup exists, or reformat (B) thinking it's a logical error, but neither addresses the physical drive deterioration signaled by SMART.

Expert Analysis

The error message "Drive failure imminent" is a specific alert generated by the Self-Monitoring, Analysis, and Reporting Technology (SMART) subsystem embedded in modern hard disk drives (HDDs) or solid-state drives (SSDs). SMART continuously monitors key drive metrics such as read/write error rates, spin-up time, mechanical wear, and bad sector counts. When these metrics exceed defined thresholds, the firmware triggers this warning to alert the user of impending hardware failure.

While the system allows the user to bypass the prompt by pressing F1 to continue working, this does not resolve the underlying physical degradation of the storage medium. The drive is at high risk of catastrophic failure, which could result in permanent data loss. Therefore, the primary objective for the help desk technician is to preserve data integrity and replace the failing component.

Option B (Reformatting) is incorrect because it addresses file system corruption, not physical hardware failure; formatting a physically failing drive will not prevent total collapse and may accelerate data loss. Option C (Rebuilding the array) assumes a RAID configuration, but the question describes a single-drive failure scenario without mentioning redundant arrays; even if RAID were present, the individual failed drive must be replaced first. Option D (Entering safe mode) is a software troubleshooting step for OS-level issues like driver conflicts or malware, which is irrelevant to a hardware-level SMART alert.

According to industry best practices and CompTIA A+ doctrine, when SMART indicates imminent failure, the immediate action is to back up critical data and then replace the drive. Since backing up is often implied as a prerequisite to replacement in exam scenarios, replacing the hard disk is the definitive corrective action listed.

Official Reference

https://www.comptia.org/certifications/a

This link opens the official vendor documentation in a new tab.

Exam Strategy

When encountering SMART or hardware-specific error messages in the CompTIA A+ exam, prioritize physical hardware replacement or backup procedures over software configurations. Differentiate between logical errors (file systems, OS settings) and physical errors (SMART, LED indicators, unusual noises). Always look for options that address the root cause of hardware degradation, such as swapping components, before considering reconfiguration steps.

Frequently Asked Questions

What does 'Drive failure imminent' mean?

It is a SMART alert indicating that the hard drive has detected physical parameters (like bad sectors or mechanical wear) suggesting it will fail soon.

Can I ignore the F1 prompt and keep using the drive?

No. While you can press F1 to boot, the drive is unstable and risks total failure, leading to data loss. Immediate backup and replacement are required.

More 220-1201 FAQ →

Community Votes

A
100%

100% of anonymous learners picked answer A. Votes are pick records left by other test-takers — they are not the verified answer.

Discussion 1 contributions

Compiled from public community threads and reader submissions, lightly edited for clarity. Handles and vote tallies are shown as recorded, and comments reflect the views of individual contributors.

From public community threads 1

  1. Afie 👍 1 Answered A
    "Drive failure imminent" is typically generated by SMART (Self-Monitoring, Analysis, and Reporting Technology) on the hard drive. SMART has detected signs of impending drive failure, such as: Bad sectors Read/write errors Mechanical wear Spin-up failures Although the user can press F1 and continue working, the drive is at high risk of failing completely at any time. Best Action ✅ Back up the user's data immediately. ✅ Replace the hard disk. ✅ Restore the data to the new drive.

Reader comments & corrections

No reader corrections yet — spotted an error or have a note? Share it below.

Log in to comment, report an error, or add a note about this question.

Practice All 220-1201 Questions

Access 105 questions with complete answers and detailed explanations.

View Full 220-1201 Practice Test →

← Back to 220-1201 Study Guide