Best way to power a redundant-server rack connection

220-1201 By islever Editorial Last updated

Short answer

C Distribute the server's power supplies across outlets fed by different UPS units so one power source failure leaves the server running.

Question

A technician is evaluating how to connect a power-redundant server to the outlets of a rack. Which of the following is the best way to provide electricity to the server?
  1. Using only one power outlet, as the system will provide energy to the redundant source
  2. Leaving one of the power supplies disconnected for use in case the other fails
  3. Identifying available power outlets in different UPSs and distributing the connection between them Correct Answer
  4. Connecting the device to one dedicated battery backup to provide continuous energy

Key Takeaways

The question tests whether redundancy extends beyond the server's power supplies to the upstream power sources; the trap is assuming one UPS or a single outlet is sufficient.

A power-redundant server should have each of its power supplies connected to outlets on different UPS units. Option C is correct because it preserves true source-level redundancy, while options A, B, and D eliminate or fail to provide it.

Common mistake: Option D is the most tempting error: a single dedicated battery backup supplies continuous power but provides no second source, so a UPS or circuit failure still takes the server down.

Expert Analysis

The governing principle

Power redundancy in a rack-mounted server means the machine ships with at least two independent power supply units (PSUs), each able to carry the full load of the system. The purpose of that hardware is lost unless each PSU is fed from an electrically separate source — a different UPS, a different power distribution unit (PDU), or a different circuit feed. This is standard data-center and rack-design practice: redundancy must exist all the way back to the power source, not just inside the chassis.

Mapping the scenario

The question specifies a power-redundant server and asks for the best way to feed the rack outlets. Option C is correct because it puts each PSU on a different UPS, so a UPS failure, circuit trip, or feed loss on one side leaves the server running on the other. A single comment on this question states the reasoning directly: connect power supply 1 to UPS A and power supply 2 to UPS B, ensuring the server survives the loss of one UPS, circuit, or power feed.

Why the others fail

Option A is wrong — a system does not generate or back-feed energy into a redundant source; a PSU only draws from the outlet it is plugged into. Option B defeats the whole design by leaving a redundant supply unplugged, so there is nothing to take over when the live PSU fails. Option D is plausible-sounding but weak: one dedicated battery backup gives only one source of energy, so a UPS fault or a single circuit problem still shuts the server down — there is no redundancy, only runtime.

Exam Strategy

When a question mentions redundancy, look for the option that creates two independent paths end to end — if both paths share any single component, they are not redundant. Eliminate any option that leaves hardware unused or disconnected, and treat battery backup as runtime protection, not redundancy, unless a second source exists. This pattern repeats across RAID, NIC-teaming, and failover questions on 220-1201.

Frequently Asked Questions

Why should each power supply of a redundant server connect to a different UPS?

Separating the PSUs across UPS units means a UPS fault, circuit trip, or feed loss on one side leaves the server powered by the other. Sharing a single UPS or circuit removes that protection.

Does connecting to one dedicated battery backup provide redundancy?

No. A single UPS gives continuous runtime but is still one point of failure. Redundancy requires at least two independent power sources feeding the server.

Why is leaving one power supply disconnected wrong?

An unplugged PSU cannot take over when the active supply fails, so the redundant hardware provides no protection and the server goes down on the first failure.

More 220-1201 FAQ →

Community Votes

C
100%

100% of anonymous learners picked answer C. Votes are pick records left by other test-takers — they are not the verified answer.

Discussion 1 contributions

Compiled from public community threads and reader submissions, lightly edited for clarity. Handles and vote tallies are shown as recorded, and comments reflect the views of individual contributors.

From public community threads 1

  1. Afie 👍 1 Answered C
    A power-redundant server has multiple power supplies designed to continue operating if one power source fails. To take full advantage of this redundancy: Connect Power Supply 1 to UPS A Connect Power Supply 2 to UPS B This ensures that if one UPS, circuit, or power feed fails, the server remains powered by the other source.

Reader comments & corrections

No reader corrections yet — spotted an error or have a note? Share it below.

Log in to comment, report an error, or add a note about this question.

Practice All 220-1201 Questions

Access 105 questions with complete answers and detailed explanations.

View Full 220-1201 Practice Test →

← Back to 220-1201 Study Guide